|
UNIVERSAL - OIL LINES
///
BACK TO TOP |
|
|
STM -4AN STAINLESS BRAIDED TURBO OIL FEED LINES
The STM -4AN Stainless Braided Turbo Oil Feed Lines are available in 4 lengths (28", 24", 18" or 14") and feature one straight end and one 90° end with swivel fittings for an easy install. Proudly made in the USA!
Universal Application.
690428,690424,690418,690414 |
|
VIBRANT STRAIGHT END OIL FEED LINES
Vibrant Performance Universal Oil Feed Kit includes a Teflon lined Stainless Steel flexible hose and high quality (straight-ended) with your choice of -4AN or -3AN fittings, pre-installed.
Universal Application.
10270,10271,10272,10275,10276,10277 |
|
|
UNIVERSAL - FITTINGS
///
BACK TO TOP |
|
|
STM -10AN TURBO OIL DRAIN FITTING (G-SERIES)
The STM -10AN G-Series Turbo Oil Drain Fitting is machined aluminum, made in Rochester, NY. These fittings typically fit the PTE Turbos and Non-Ball-Bearing Garrett Turbos among many other applications. Fitting measures 2" from bolt-hole to bolt-hole. Gasket is included.
Universal Application.
STM-ODF-G |
|
STM -10AN TURBO OIL DRAIN FITTING (GT-SERIES)
The STM -10AN G-Series Turbo Oil Drain Fitting is machined aluminum, made in Rochester, NY. These fittings typically fit the GT Garrett Series, most T3 FP Turbos among many other applications. Fitting measures 1.5" from bolt-hole to bolt-hole. Gasket is included.
Universal Application.
STM-ODF-GT |
|
STM -10AN TURBO OIL DRAIN FITTING (MITSU-SERIES)
The STM -10AN Mitsu-Series Turbo Oil Drain Fitting is machined aluminum, made in Rochester, NY. These fittings typically fit the Mitsubishi 14B, 16G, T25, T28 and bolt-on Evo 8/9 turbos among many other applications. Fitting measures 1.5" from bolt-hole to bolt-hole. Gasket is included.
Universal Application.
STM-ODF-MIT |
|
VIBRANT 1/8" TURBO OIL FEED FLANGE
The Vibrant Performance Turbo Oil Feed Flange is designed for Garrett T3, T3/T4 and T04 turbos that do not have a tapped oil feed inlet and therefore a flange must be used for installing the oil feed line.
Universal Application.
2899 |
|
VIBRANT TURBO OIL FLANGE FOR GT32-GT55R TURBOS
The Vibrant Performance Turbo Oil Flange is designed to be used with GT32-GT55R turbos. Made of T6061 billet aluminum and the center hole is threaded for a 1/2" NPT fitting. Includes two M8 x 1.25 bolts.
Universal Application.
2853 |
|
VIBRANT TURBO OIL DRAIN FLANGE FOR T3, T3/T4 & T04 TURBOS
The Vibrant Performance Turbo Oil Drain Flange is designed to be used with T3, T3/T4 and T04 turbos. Made of T6061 billet aluminum and the center hole is threaded for a 1/2" NPT fitting. Includes two M8 x 1.25 bolts.
Universal Application.
2898 |
|
VIBRANT TURBO OIL DRAIN FLANGE FOR GT SERIES BB TURBOS
The Vibrant Performance Turbo Oil Drain Flange is designed to be used with GT25R, GT28R, GT30R and GT35R ball bearing turbos. Made of T6061 billet aluminum and the center hole is threaded for a 1/2" NPT fitting. Includes two M8 x 1.25 bolts.
Universal Application.
2889 |
|
VIBRANT TURBO OIL DRAIN FLANGE WITH -10AN FITTING FOR GT15-GT35 TURBOS
The Vibrant Performance Turbo Oil Drain Flange with -10AN Fitting is designed to be used with GT15-GT35 turbos. Made of T6061 billet aluminum and CNC machined with a -10AN fitting. Includes two M8 x 1.25 bolts.
Universal Application.
2893 |
|
STM GARRETT DUAL BALL-BEARING OIL RESTRICTOR FITTING
The STM Garrett Dual Ball-Bearing Oil Restrictor Fitting features a .035" restrictor hole size and works with Garrett GT30/35R style turbos or any turbo requiring a 7-1/16" x 24 inverted flare restrictor fitting.
Universal Application.
STM-10716-04TR |
|
STM 3/8" BSPT TO -4AN FITTING
The STM 3/8" BSPT to -4AN Fitting is generally used to attach a turbo oil feed line to your 3/8" BSPT oil filter housing.
Universal Application.
STM-742-04-06S |
|
-4AN 90° TO 3/8" NPT MALE STEEL TURBO ADAPTER FITTING
-4AN 90° to 3/8" NPT Male Steel Adapter Turbo Oil Fitting.
Universal Application.
TF-782246 |
|
VIBRANT OIL RESTRICTOR FITTINGS WITH ADJUSTABLE JETS
These Vibrant Performance PTFE Lined Stainless Steel Oil Restrictor Fittings include two different sized fittings, allowing you to effectively limit oil flow to your turbo, thereby minimizing the potential for damaging the oil seals.
Universal Application.
10289,10288,10287 |
|
STM BALL BEARING WATER LINE BANJO BOLT KIT (18MM x 1.5)
The STM Ball Bearing Water Line Banjo Bolt Kit is comprised of high-quality fittings and copper crush washers to allow you to adapt a -6AN hose to the water jackets of your turbo. Fits GT37 and larger housings or any turbo that requires M18 x 1.5mm fittings.
Universal Application.
STM-WBK-186 |
|
STM BALL BEARING WATER LINE BANJO BOLT KIT (14MM x 1.5)
The STM Ball Bearing Water Line Banjo Bolt Kit is comprised of high-quality fittings and copper crush washers to allow you to adapt a 3/8" hose to the water jackets of your turbo. Fits T2, GT25, GT30, GT35 and MHI TD05 housings or any turbo that requires M14 x 1.5mm fittings.
Universal Application.
STM-WBK-146 |
|
TECHNA-FIT UNIVERSAL BANJO BOLTS
Techna-Fit Steel Banjo Bolts are sold individually below and the perfect source for your custom brakes or turbo oil lines.
Universal Application.
TF-775 |
|
TECHNA-FIT UNIVERSAL BANJO FITTINGS
Techna-Fit Steel Banjo Fittings are sold individually below and the perfect source for your custom fluid lines.
Universal Application.
TF-776,TF-P776 |
|
COPPER CRUSH WASHERS FOR BANJO BOLTS
Universal Copper Crush Washers for Banjo Bolts are available in sizes from 10, 12, 14, 16 and 18mm.
Universal Application.
CCW |
|
|
UNIVERSAL - OIL FILTERS
///
BACK TO TOP |
|
|
FP -4AN IN-LINE RED OIL FILTER FOR JOURNAL BEARING TURBOS
The body of the red filter features a built in .125" orifice for full flow journal bearing turbos. The Forced Performance -4AN In-Line Oil Filter is made with female 4AN at the inlet side and male 4AN at the outlet side. This allows the filter to install into virtually any 4AN line without additional fittings.
For Journal Bearing Turbos.
FP-4ANFILTER-RED |
|
FP -4AN IN-LINE BLACK OIL FILTER FOR BALL BEARING TURBOS
The body of the black filter features a built in .030" restrictor as recommended by Garrett for use with their GT25R, GT30R, GT35R cartridges. The Forced Performance -4AN In-Line Oil Filter is made with female 4AN at the inlet side and male 4AN at the outlet side. This allows the filter to install into virtually any 4AN line without additional fittings.
For Ball-Bearing Turbos.
FP-4ANFILTER-BLK |
|
FP REPLACEMENT -4AN OIL FILTER ELEMENT
The Forced Performance Replacement Filter Element and O-Ring for the FP -4AN Inline Oil Filters fits both the black and red filter styles.
Fits FP -4AN Black and Red Filters
FILTERELEMENT |
|
EARL'S -4AN INLINE OIL FILTER
Earl's Performance has your pluming needs covered with these screen-type inline oil filters. They are designed for use as pre-filters for fuel and oil systems. They easily disassemble for inspection and cleaning to get the job done right the first time around.
Universal Application.
AT230204ERL |
|
|
UNIVERSAL - TURBO & OIL GASKETS
///
BACK TO TOP |
|
|
STM STAINLESS STEEL T3 TURBO INLET GASKET
The STM T3 Turbo Inlet Gasket features a 14 gauge thickness, cut from T304 Stainless Steel and made in the USA!
Universal Application.
STM-SSG-T3I |
|
T4 DIVIDED TURBO GASKET
Vibrant Performance Stainless Steel T4 Divided Turbo Gasket.
Universal Application.
1442G |
|
T4 UNDIVIDED TURBO GASKET
Vibrant Performance Stainless Steel T4 Undivided Turbo Gasket.
Universal Application.
1441G |
|
GT SERIES TURBO GASKET
Vibrant Performance Stainless Steel GT Series Turbo Gasket. 3" for newer generation GT housings and 2.5" available.
Universal Application.
1439G,1438G |
|
OEM MITSUBISHI TURBO OIL RETURN GASKET
Genuine OEM Mitsubishi Turbo Oil Return Gasket fits the Evolution VIII & IX, 2008-2015 Evolution X, 1G & 2G DSM and 3000GT & Stealth.
Mitsubishi Applications.
MR258477 |
|
STM TURBO OIL DRAIN FITTING GASKET (G-SERIES)
The STM Turbo Oil Drain Fitting Gasket typically fits the PTE Turbos and Non-Ball-Bearing Garrett Turbos among many other applications. Measures 2" from bolt hole to bolt hole.
Universal Application.
STM-GSK-ODF-G |
|
STM TURBO OIL DRAIN FITTING GASKET (GT-SERIES)
The STM Turbo Oil Drain Fitting Gasket typically fits the GT Garrett Series, most T3 FP Turbos among many other applications. Measures 1.5" from bolt hole to bolt hole.
Universal Application.
STM-GSK-ODF-GT |
|
|
UNIVERSAL - BOOST LEAK TESTERS
///
BACK TO TOP |
|
|
STM BOOST LEAK TESTERS
One of the easiest ways to lose power is to have a simple leak in your system. The STM Boost Leak Tester comes with the STM Reducer Coupler to match your turbo inlet from 1.75" to 4" compressor, T-Clamps and 3" aluminum coupler with nozzle to test your boost pressure and ensure your set-up is solid.
Universal Application.
STM BOOST LEAK TESTER |
|
|
UNIVERSAL - COMPRESSOR OUTLET PIPES
///
BACK TO TOP |
|
|
STM 2.5" 90° COMPRESSOR OUTLET PIPE KIT
This STM 2.5" 90° Compressor Outlet Pipe Kit allows you to take a down-firing or up-firing 2.5" compressor outlet and bring it to either side, where most intercooler piping is typically located. We include new stainless T-clamps, a 2.5" brushed aluminum joiner in a 6" or 8" length and a 2.5" high-quality 90° silicone coupler with 10" legs that you can easily cut to fit your exact set-up.
Universal Application.
STM-COM-OUT-PK-2.5 |
|
