|
SUBARU WRX & STi - GAUGE INSTALLATION
///
BACK TO TOP |
|
|
BOOST GAUGE INSTALL KIT
This allows you to tap your mechanical gauge that uses the 1/8 tubing as a feed line.
Universal Application.
STM-BGIK |
|
PIGTAIL FUSES
Trying to find a power source for your gauges? These nifty, little things will do the trick!
Universal Application.
STM-PIGF |
|
PROSPORT OIL GALLEY PLUG (SUBARU WRX & STi)
This plug replaces the stock main oil galley plug located on the drivers side. It has a threaded center to allow the installation of any 1/8" NPT Sender. Makes installation of Oil Pressure/Oil Temperature Senders easy by just replacing one of three stock oil galley locations.
Universal Application.
PS-NUT |
|
PROSPORT OIL FILTER ADAPTER PLATE (M20 x 1.5)
This is a great product from Prosport to make installing your Oil Pressure and Oil Temperature senders easy. This plate screws on under your oil filter and it has 4 1/8"NPT fittings. M20 x 1.5 fits most Subaru, Non-metric Honda, Mitsubishi, Acura, Hyundai, Nissan Sentra 2.5L & Mazda RX-7, RX-8 & S2000.
Universal Application.
PSOPOT M20XP1.5 |
|
PROSPORT WATER TEMP SENSOR ADAPTER
This will place the temperature sensor directly in the stream of the water towards the radiator without absorbing transient heat from the engine block for accurate readings of the water temperature. Four sizes are available for the perfect fit for just about any engine application and stays water-tight to prevent leaks with the provided hose clamps. Each adapter features an 1/8 NPT fitting.
Universal Application.
PSWT3 |
|
TUBING FOR MECHANICAL PSI GAUGES
Auto Meter Nylon Tubing for Mechanical Pressure Gauges. Does not accommodate fuel pressure or models 5423 & 5426.
Universal Application.
3223 |
|
AUTOMETER ADAPTER (1/8" NPT-BSPT)
Autometer Metric Gauge Adapter. 1/8" NPT Female to 1/8" BSPT Male Adapter.
Universal Application.
2269 |
|
-4AN MALE TO 1/8 NPT FEMALE ADAPTER FITTING
-4AN Male to 1/8 NPT Female Adapter Fitting.
Universal Application.
TF-GA-04 |
|
3M SUPER 33+ ELECTRICAL TAPE
Scotch® Vinyl Electrical Tape 33 is a quality, general-purpose vinyl insulating tape. It has excellent resistance to: abrasion, moisture, alkalies, acid, copper corrosion and varying weather conditions.
3/4" x 52' Roll.
3MET33-10 |
|
PROFITTER 500° LOW DENSITY PTFE PIPE TAPE
1/2" x 520" roll pipe sealing tape.
1/2" x 520" Roll.
63164 |
|
VIBRANT POLYETHYLENE AIR LINE TUBING
Flexible, lightweight and durable. Suitable for air lines and instrumentation and capable of Withstanding operating pressures up to 100 PSI and temperatures up to 140°F. Sold in a 10 foot roll and available in three diameters: 5/32", 3/8" and 1/4".
Universal Application.
2650,2651,2652 |
|
SILICONE VACUUM HOSE
High quality, thick-walled, pure silicone hose in 3mm, 4mm and 6mm.
Sold Per Foot.
XXXXXX |
|
BLACK T-FITTINGS
Black T Vacuum Fittings. 3, 4 and 6mm sizes.
Universal Application.
10110,10109,12926,10108 |
|
|
SUBARU WRX & STi - OXYGEN SENSORS & PARTS
///
BACK TO TOP |
|
|
OEM SUBARU OXYGEN SENSORS
Genuine OEM Subaru Oxygen Sensors.
2008-2014 Subaru WRX & STi
2002-2007 Subaru WRX & STi.
22641AA510,22690AA850,22690AA491,22690AA520 |
|
AEM REPLACEMENT 4.9LSU BOSCH OXYGEN SENSOR
AEM Replacement 4.9LSU Bosch Oxygen Sensor for new AEM Digital Wideband UEGO Air/Fuel Gauge 30-4110.
Universal Application.
30-2004 |
|
AEM REPLACEMENT 4.2LSU BOSCH OXYGEN SENSOR
AEM Replacement 4.2LSU Bosch Oxygen Sensor for original AEM Wideband UEGO Air/Fuel Gauges.
Universal Application.
30-2001 |
|
AUTOMETER NARROW BAND O2 SENSOR KIT
Auto Meter Narrow Band O2 Sensor Kit for use with narrow band air/fuel ratio gauges.
Universal Application.
2244 |
|
INNOVATE REPLACEMENT 02 SENSOR (LSU 4.2)
Bosch LSU 4.2 5-Wire Wide-Band O2 Sensor. Compatible with Innovate Motorsports LM-1, LM-2, LC-1, and LC-1ST.
Universal Application.
3737 |
|
INNOVATE REPLACEMENT 02 SENSOR (LSU 4.9)
Bosch LSU 4.9 5-Wire Wide-Band O2 Sensor. Compatible with Innovate Motorsports LM-2, LC-2, and MTX-L, SCG-1, DLG-1, PSB-1, and PSN-1.
Universal Application.
17025,3888 |
|
NGK NTK REPLACEMENT O2 SENSOR
NGK / NTK replacement oxygen sensor sensor for the AFX wideband monitor.
Universal Application.
24302 |
|
|
SUBARU WRX & STi - MAF, MAS, MAP & AIT
///
BACK TO TOP |
|
|
OMNI POWER SUBARU MAP SENSORS
Omni Power USA 3 & 4 Bar MAP (Manifold Absolute Pressure) sensors use state of the art bipolar op amp circuitry with thin film resistor networks built into each micro chip. 260°F to -40°F temperature operating range. Will require a change in tune.
2004-2014 Subaru STi.
2006-2007 Subaru WRX.
MAP-STI-3BR,MAP-STI-4BR |
|
OMNI POWER SUBARU MAP SENSORS
Omni Power USA 3 & 4 Bar MAP (Manifold Absolute Pressure) sensors use state of the art bipolar op amp circuitry with thin film resistor networks built into each micro chip. 260°F to -40°F temperature operating range. Will require a change in tune.
2008-2014 Subaru WRX.
MAP-SUP-3BR,MAP-SUP-4BR |
|
AEM REPLACEMENT MAP SENSOR KITS
AEM Replacement MAP Sensor Kits include stainless steel sensor, connector, pins, 1/8" NPT to -4AN adapter & 1/8" NPT to 3/16" barb adapter. 1, 2, 3.5 and 5 BAR.
Universal Application.
30-2130-15,30-2130-30,30-2130-50,30-2130-75 |
|
AEM MAP SENSOR CONNECTOR
AEM Map Sensor Connector.
Universal Application.
35-2131 |
|
AEM TRU-BOOST 5 BAR MAP SENSOR UPGRADE KIT
AEM Tru-Boost 5 Bar MAP Sensor Upgrade Kit allows your Tru-Boost gauge the capability to read boost up to 50 psi.
Universal Application.
30-4351 |
|
AEM AIR INLET TEMPERATURE SENSOR
Air inlet temperature sensor kit. Includes aluminum weld-in bung, connector plug with flying lead & sensor.
Universal Application.
30-2010 |
|
STM UNIVERSAL GM AIR INTAKE TEMPERATURE SENSOR KIT
For a less expensive option to the AEM sensors, The STM GM Air Intake Temperature Sensor Kit includes an aluminum weld-on bung for your pipe, GM AIT sensor and matching pigtail harness.
Universal Application.
STM-GMAIT |
|
DURALAST GM AIT SENSOR PIGTAIL HARNESS
Duralast GM air intake temperature sensor female pigtail harness. Typically used with Mitsubishi DSM & Evolution speed density conversions.
Universal Application.
235 |
|
DURALAST GM AIT SENSOR
Duralast GM 3/8" NPT air intake temperature sensor. Typically used with Mitsubishi DSM & Evolution speed density conversions
Universal Application.
SU-107 |
|
|
SUBARU WRX & STi - ENGINE, GAUGE & MISC SENSORS
///
BACK TO TOP |
|
|
CRANKSHAFT SENSOR
Genuine OEM Subaru Crankshaft Sensor.
2002-2014 Subaru WRX.
2004-2015 Subaru STi.
22053AA053 |
|
AEM REPLACEMENT PRESSURE SENSOR KITS
AEM Replacement PSIg pressure sensors are available from 100-2000 psi for boost, EGT, nitrous, brake pressure, inlet air temperature, or UEGO replacement gauges.
Universal Application.
30-2130-100,30-2130-150,30-2130-500,30-2130-1000,30-2130-2000 |
|
AEM REPLACEMENT FLUID PRESSURE SENSORS
AEM Replacement Fluid Pressure Sensors are available for 15, 35, 50, 100 and 150 PSI boost and fluid ranges. Compatible with AEM Analog and Digital Gauges.
Universal Application.
30-2131-15G,30-2131-50,30-2131-75,30-2131-100,30-2131-150 |
|
|
AEM REPLACEMENT FLUID PRESSURE SENSORS
AEM Replacement Fluid Pressure Sensors are available for 15, 35, 50, 100 and 150 PSI boost and fluid ranges. Compatible with AEM Analog and Digital Gauges.
Universal Application.
30-2131-15G,30-2131-50,30-2131-75,30-2131-100,30-2131-150 |
|
AEM REPLACEMENT FLUID TEMPERATURE SENSOR KIT
AEM Replacement Oil/Trans/Water Temperature Sensor Kit includes the 1/8"NPT temperature sensor, plug, pins & pin lock. Compatible with digital and analog gauges.
Universal Application.
30-2012 |
|
AEM REPLACEMENT METHANOL INJECTION MONITOR SENSOR
AEM Replacement Methanol Injection Monitor Sensor.
Universal Application.
35-2128 |
|
AEM REPLACEMENT ANALOG EGT K-TYPE SENSOR
AEM Replacement EGT Sensor for Analog Gauges. K-Type Closed Tip Thermocouple Sensor.
Universal Application.
30-2065 |
|
AEM EXHAUST GAS TEMPERATURE SENSOR KIT
The AEM 30-2050 EGT Sensor Kit is a RTD type EGT sensor with an inconel body, M14 x 6H. It includes an RTD temp sensor with male thread, a weld-on bung with female thread, connector and pins and offers a heat range of -40°F to 1832°F.
Universal Application.
30-2050 |
|
AEM UNIVERSAL 12 POSITION TRIM POT
The AEM Universal 12 Position Trim Pot is for use on virtually any Engine Management System, such as the AEM EMS. Use the Trim Pot to adjust a number of trims, including ignition timing, fuel, boost, etc.
Universal Application.
30-2056 |
|
|
SUBARU WRX & STi - CABLES & HARNESSES
///
BACK TO TOP |
|
|
AEM INFINITY SERIES 7 UNIVERSAL PLUG & PIN KIT
The AEM Infinity Series 7 Universal Plug & Pin Kit includes (1) 73-pin connector with cover, (1) 56-pin connector with cover, 130 small pins, 1 large pin with weather seal, 1 micro relay with pins, and 30 sealing plugs. AEM offers several different wiring harness types and configurations to simplify the process of wiring the Infinity ECU to your vehicle.
Universal Application.
30-3701 |
|
AEM INFINITY SERIES 7 UNIVERSAL WIRING HARNESS
The AEM Infinity Series 7 Universal Wiring Harness includes pre-wired power and grounds, power relay, fuse box, dual wideband connectors, AEMnet connector (CAN), 100 X 96" terminated wires for population and 12 small pins. AEM offers several different wiring harness types and configurations to simplify the process of wiring the Infinity ECU to your vehicle.
Universal Application.
30-3702 |
|
AEM INFINITY SERIES 7 MINI UNIVERSAL WIRING HARNESS
The AEM Infinity Series 7 Mini Universal Harness includes pre-wired power and grounds, power relay, fuse box, dual wideband connectors, AEMnet connector (CAN), 100 small pins with 30 sealing plugs. AEM offers several different wiring harness types and configurations to simplify the process of wiring the Infinity ECU to your vehicle.
Universal Application.
30-3703 |
|
AEM INFINITY SERIES 5 PLUG & PIN KIT
The AEM Infinity Series 5 Plug & Pin Kit includes 80 pin connector with cover, 80 small pins, 1 micro relay with pins and 30 sealing plugs. AEM offers several different wiring harness types and configurations to simplify the process of wiring the Infinity ECU to your vehicle.
Universal Application.
30-3704 |
|
AEM INFINITY SERIES 5 MINI UNIVERSAL WIRING HARNESS
The AEM Infinity Series 5 Mini Universal Harness includes pre-wired power, grounds, power relay, fuse box, single wideband & AEMnet, 80 small pins and 30 sealing plugs. AEM offers several different wiring harness types and configurations to simplify the process of wiring the Infinity ECU to your vehicle.
Universal Application.
30-3705 |
|
AEM INFINITY SERIES 5 UNIVERSAL MINI FLYING LEAD HARNESS
The AEM Infinity Series 5 Universal Mini Flying Lead Harness includes pre-wired power, grounds, power relay, single wideband, 8 x coils & 8 x injectors. I/O wiring includes TPS, MAP, CLT, AIT, +5V, Sensor Ground, Fan, Tach & 2 Step. 10 x 96" 22ga Terminated wire and 2 x 96" Terminated 2-Pair Twisted/Shielded Wire. AEM offers several different wiring harness types and configurations to simplify the process of wiring the Infinity ECU to your vehicle.
Universal Application.
30-3706 |
|
AEM INFINITY 02 SENSOR EXTENSION HARNESS
The AEM Infinity 02 Sensor Extension Harness allows you to connect your AEM wideband O2 air/fuel ratio sensors to the Infinity's on-board wideband UEGO controllers. 72" length.
Universal Application.
30-3600 |
|
AEM INFINITY AUX HARNESS FOR AIT AND MAP SENSOR
The AEM Infinity Aux Harness for AIT and MAP Sensor allows you to connect your AEM AIT and MAP sensors to the Infinity's Aux Deuatch Plug. 72" length.
Universal Application.
30-3510-00 |
|
AEM INFINITY IP67 COMMUNICATIONS CABLE
Protect your AEM Infinity ECU by using IP67-rated communications cables. They are completely dustproof and are rated waterproof to 1 meter.
Universal Application.
30-3601 |
|
AEM INFINITY IP67 LOGGING CABLE
Protect your AEM Infinity ECU by using IP67-rated communications cables. They are completely dustproof and are rated waterproof to 1 meter.
Universal Application.
30-3602 |
|
COBB AP3 OBDII UNIVERSAL ACCESSPORT CABLE
Tired of your Accessport OBDII cable getting in the way? The new COBB OBDII Universal Cable features a much lower profile OBD connector design. The 6ft cable allows for a cleaner installation when choosing to route behind the dash.
Universal Application.
AP3-OBDII-CABLE-UNIVERSAL |
|
COBB TUNING 2002 WRX BLUE INITIALIZATION CONNECTOR
The 2002 WRX requires the use of this particular Initialization ("init") Connector in order to get the car into Test Mode, which is when there is open communication with the ECU and a Reflash is possible.
2002 Subaru WRX.
AE-WRX-FLASHMODE-02 |
|
COBB TUNING 2003-2005 WRX WHITE INITIALIZATION CONNECTOR
The 2003-2005 WRX requires the use of this particular Initialization ("init") Connector in order to get the car into Test Mode, which is when there is open communication with the ECU and a Reflash is possible.
2003-2005 Subaru WRX.
AE-WRX-FLASHMODE-03 |
|
AEM PRESSURE SENSOR REPLACEMENT HARNESS FOR DIGITAL GAUGES
The AEM Digital Boost/Pressure Gauge Replacement Cable replaces your old, damaged harness. This 8 foot cable fits AEM Digital Gauges (30-4401, 30-4406, 30-4407 & 30-4408).
Universal Application.
35-3405 |
|
AEM PRESSURE SENSOR REPLACEMENT HARNESS FOR ANALOG GAUGES
AEM 96" Sensor Replacement Harness for Analog Boost/Fuel/Oil Pressure Gauges.
Universal Application.
35-3412 |
|
AEM REPLACEMENT TRU-BOOST 5 BAR MAP SENSOR HARNESS
AEM 96" Replacement Harness for Tru-Boost 5 Bar MAP Sensor Upgrade
Universal Application.
35-3410 |
|
AEM TRU-BOOST GAUGE REPLACEMENT CABLE
The AEM True-Boost Replacement Cable fits the AEM Digital Tru-Boost Gauge (30-4350) and is 8 feet long.
Universal Application.
35-3409 |
|
AEM REPLACEMENT UEGO POWER HARNESS
The AEM Replacement UEGO Power Harness is compatible with both the Bosch 4.2 & 4.9 LSU sensors. 36" length.
Universal Application.
35-3401 |
|
AEM REPLACEMENT UEGO 4.2LSU OXYGEN SENSOR HARNESS
AEM 96" Replacement UEGO 4.2LSU Oxygen Sensor Harness.
Universal Application.
35-3400 |
|
AEM REPLACEMENT UEGO 4.9LSU OXYGEN SENSOR HARNESS
AEM 96" Replacement UEGO 4.9LSU Oxygen Sensor Harness.
Universal Application.
35-3441 |
|
AEM WIDEBAND FAILSAFE O2 SENSOR REPLACEMENT HARNESS
AEM 96" 4.2LSU O2 Sensor Replacement Harness for Wideband Failsafe Gauge 30-4900.
Universal Application.
35-3426 |
|
AEM REPLACEMENT ANALOG TEMPERATURE SENSOR HARNESS
AEM 96" Replacement Temperature Sensor Harness for the Oil/Transmission/Water Temp Analog Gauges.
Universal Application.
35-3413 |
|
AEM DIGITAL VOLT GAUGE POWER REPLACEMENT HARNESS
AEM 36" Power Replacement Harness for Digital Volt Gauge 30-4400.
Universal Application.
35-3403 |
|
AEM DIGITAL TEMPERATURE GAUGE REPLACEMENT HARNESS
AEM 96" Replacement Harness for the Digital Oil/Transmission/Water Temperature Gauge 30-4402.
Universal Application.
35-3404 |
|
AEM REPLACEMENT METH FLOW/FAILSAFE GAUGE USB CABLE
AEM 96" Replacement USB Cable for AEM Meth Flow/Failsafe Gauges.
Universal Product.
35-3415 |
|
AEM REPLACEMENT ANALOG EGT SENSOR HARNESS
AEM 96" Replacement EGT Sensor Harness for Analog Gauges.
Universal Application.
35-3414 |
|
AEM WIDEBAND FAILSAFE REPLACEMENT POWER HARNESS
AEM 36" Replacement Power Harness for the Wideband Failsafe Gauge 30-4900.
Universal Application.
35-3425 |
|
AEM ANALOG GAUGE POWER HARNESS
AEM 36" Power Replacement Cable for Analog Gauges.
Universal Application.
35-3411 |
|
AEM REPLACEMENT METH FAILSAFE OUTPUT HARNESS
AEM 36" Replacement Output Harness for Water/Methanol Failsafe Gauges.
Universal Product.
35-3418 |
|
|
SUBARU WRX & STi - SOLENOIDS
///
BACK TO TOP |
|
|
GRIMMSPEED 3-PORT ELECTRONIC BOOST CONTROL SOLENOIDS
Revolutionizing the boost solenoid market, GrimmSpeed has created model specific install brackets for a factory fit and finish. Features a plug & play fit to the OEM harness. GrimmSpeed worked with many of the top tuners in the country to ensure that this solenoid works safely with the factory ECU.
Subaru WRX & STi Models
057001,057032,057002,057007 |
|
AEM BOOST CONTROL SOLENOID
AEM's Boost Control Solenoid is specifically manufactured for automotive applications. It is designed to resist corrosion and sticking from exposure to rich fuel mixtures. AEM's Boost Control Solenoid is pressure tested to 100 PSI and includes 1/8" NPT to 3/8" barb fittings to reduce any chance of leaks.
Universal Application.
30-2400 |
|
PERRIN 3-PORT ELECTRONIC BOOST CONTROL SOLENOID
The EBCS PRO operates almost 2 times faster than other designs, allowing almost 50% more airflow, and works with OEM ECUs without causing check engine lights. To fully utilize the EBCS Pro, an ECU recalibration is NEEDED to ensure no overboosting occurs. The OEM male connector is specific to all Subaru and Mitsubishi applications. Includes additional brackets to allow universal applications.
Universal Application.
ASM-TAC-726 |
|
