NISSAN > R35 GT-R > ELECTRONICS, BATTERY & IGNITION > SENSORS & INSTALL ACCESSORIES

R35 GT-R - GAUGE INSTALLATION      ///      BACK TO TOP
	BOOST GAUGE INSTALL KIT This allows you to tap your mechanical gauge that uses the 1/8 tubing as a feed line. Universal Application. STM-BGIK
	PIGTAIL FUSES Trying to find a power source for your gauges? These nifty, little things will do the trick! Universal Application. STM-PIGF
	PROSPORT WATER TEMP SENSOR ADAPTER This will place the temperature sensor directly in the stream of the water towards the radiator without absorbing transient heat from the engine block for accurate readings of the water temperature. Four sizes are available for the perfect fit for just about any engine application and stays water-tight to prevent leaks with the provided hose clamps. Each adapter features an 1/8 NPT fitting. Universal Application. PSWT3
	TUBING FOR MECHANICAL PSI GAUGES Auto Meter Nylon Tubing for Mechanical Pressure Gauges. Does not accommodate fuel pressure or models 5423 & 5426. Universal Application. 3223
	AUTOMETER ADAPTER (1/8" NPT-BSPT) Autometer Metric Gauge Adapter. 1/8" NPT Female to 1/8" BSPT Male Adapter. Universal Application. 2269
	-4AN MALE TO 1/8 NPT FEMALE ADAPTER FITTING -4AN Male to 1/8 NPT Female Adapter Fitting. Universal Application. TF-GA-04
	3M SUPER 33+ ELECTRICAL TAPE Scotch® Vinyl Electrical Tape 33 is a quality, general-purpose vinyl insulating tape. It has excellent resistance to: abrasion, moisture, alkalies, acid, copper corrosion and varying weather conditions. 3/4" x 52' Roll. 3MET33-10
	PROFITTER 500° LOW DENSITY PTFE PIPE TAPE 1/2" x 520" roll pipe sealing tape. 1/2" x 520" Roll. 63164
	VIBRANT POLYETHYLENE AIR LINE TUBING Flexible, lightweight and durable. Suitable for air lines and instrumentation and capable of Withstanding operating pressures up to 100 PSI and temperatures up to 140°F. Sold in a 10 foot roll and available in three diameters: 5/32", 3/8" and 1/4". Universal Application. 2650,2651,2652
	SILICONE VACUUM HOSE High quality, thick-walled, pure silicone hose in 3mm, 4mm and 6mm. Sold Per Foot.
	BLACK T-FITTINGS Black T Vacuum Fittings. 3, 4 and 6mm sizes. Universal Application. 10110,10109,12926,10108
R35 GT-R - OXYGEN SENSORS & PARTS      ///      BACK TO TOP
	OEM NISSAN FRONT PRIMARY OXYGEN SENSOR Genuine OEM Nissan Front Primary Oxygen Sensors. Primary (Bank 2) USDM (LH) Driver Side. Primary (Bank 1) USDM (RH) Passenger Side. 2009+ Nissan R35 GT-R. 22693-JF00B,22693-JF00A
	OEM NISSAN HEATED REAR OXYGEN SENSOR Genuine OEM Nissan Heated Rear Oxygen Sensor. 2009+ Nissan R35 GT-R. 226A0-EN21A
	AEM REPLACEMENT 4.9LSU BOSCH OXYGEN SENSOR AEM Replacement 4.9LSU Bosch Oxygen Sensor for new AEM Digital Wideband UEGO Air/Fuel Gauge 30-4110. Universal Application. 30-2004
	AEM REPLACEMENT 4.2LSU BOSCH OXYGEN SENSOR AEM Replacement 4.2LSU Bosch Oxygen Sensor for original AEM Wideband UEGO Air/Fuel Gauges. Universal Application. 30-2001
	AUTOMETER NARROW BAND O2 SENSOR KIT Auto Meter Narrow Band O2 Sensor Kit for use with narrow band air/fuel ratio gauges. Universal Application. 2244
	INNOVATE REPLACEMENT 02 SENSOR (LSU 4.2) Bosch LSU 4.2 5-Wire Wide-Band O2 Sensor. Compatible with Innovate Motorsports LM-1, LM-2, LC-1, and LC-1ST. Universal Application. 3737
	INNOVATE REPLACEMENT 02 SENSOR (LSU 4.9) Bosch LSU 4.9 5-Wire Wide-Band O2 Sensor. Compatible with Innovate Motorsports LM-2, LC-2, and MTX-L, SCG-1, DLG-1, PSB-1, and PSN-1. Universal Application. 17025,3888
	NGK NTK REPLACEMENT O2 SENSOR NGK / NTK replacement oxygen sensor sensor for the AFX wideband monitor. Universal Application. 24302
R35 GT-R - MAF, MAS, MAP & AIT      ///      BACK TO TOP
	OMNI POWER 4 BAR MAP SENSOR Omni Power 4 bar MAP sensors can precisely calculate boost pressure from 1-43+ psi while still allowing smooth stock OEM drivability at any boost level. Conveniently packaged in an OEM dimensional housing for easy install and an OEM look. 2009+ Nissan R35 GT-R. MAP-GTR-4BR
	AMS ALPHA 4 BAR MAP SENSOR UPGRADE AMS now brings you a simple solution for reliable and precise boost control with a simple, seamless integration into your GT-R. By utilizing a 4-bar sensor you are able to regain control of your boost accurately up to 44 psi and also allows for better data collection for the Tuner resulting in a more accurate and safer tune on the dyno. 2009+ Nissan R35 GT-R. AMS,4BAR,MAP
	OMNI POWER 4 BAR SPEED DENSITY HARNESS The Omni Power 4 Bar Plug And Play Speed Density Conversion Harness for the R35 GT-R includes a 4 bar t-map sensor, plus the standard 4 bar GTR map sensor along with a factory-look wire harness. 2009+ Nissan R35 GT-R. HAR-GTR-SD
	GOTBOOST PERFORMANCE SPEED DENSITY KIT GotBoost Performance is proud introduce the world's first complete Mass Air Flow (MAF) Delete and Intake Air Temperature (IAT) conversion kit for the Nissan GT-R R35. Two options are available, click for more information. 2009+ Nissan R35 GT-R. XXXXXX
	AMS ALPHA MASS AIR FLOW SENSORS Through research and development and extensive testing, AMS took the route of properly scaling new MAF sensors to eliminate the limp mode and regain the use of the automatic transmission setting. These perfectly re-scaled custom AMS MAF sensors allow you to run a properly designed intake setup with no restriction to hp, and also allows you to make the car drive like stock while retaining the factory air temperature sensor. 2009+ Nissan R35 GT-R. AMS MASS FLOW
	AEM REPLACEMENT MAP SENSOR KITS AEM Replacement MAP Sensor Kits include stainless steel sensor, connector, pins, 1/8" NPT to -4AN adapter & 1/8" NPT to 3/16" barb adapter. 1, 2, 3.5 and 5 BAR. Universal Application. 30-2130-15,30-2130-30,30-2130-50,30-2130-75
	AEM MAP SENSOR CONNECTOR AEM Map Sensor Connector. Universal Application. 35-2131
	AEM TRU-BOOST 5 BAR MAP SENSOR UPGRADE KIT AEM Tru-Boost 5 Bar MAP Sensor Upgrade Kit allows your Tru-Boost gauge the capability to read boost up to 50 psi. Universal Application. 30-4351
	AEM AIR INLET TEMPERATURE SENSOR Air inlet temperature sensor kit. Includes aluminum weld-in bung, connector plug with flying lead & sensor. Universal Application. 30-2010
	STM UNIVERSAL GM AIR INTAKE TEMPERATURE SENSOR KIT For a less expensive option to the AEM sensors, The STM GM Air Intake Temperature Sensor Kit includes an aluminum weld-on bung for your pipe, GM AIT sensor and matching pigtail harness. Universal Application. STM-GMAIT
	DURALAST GM AIT SENSOR PIGTAIL HARNESS Duralast GM air intake temperature sensor female pigtail harness. Typically used with Mitsubishi DSM & Evolution speed density conversions. Universal Application. 235
	DURALAST GM AIT SENSOR Duralast GM 3/8" NPT air intake temperature sensor. Typically used with Mitsubishi DSM & Evolution speed density conversions Universal Application. SU-107
R35 GT-R - ENGINE, GAUGE & MISC SENSORS      ///      BACK TO TOP
	OEM NISSAN BOOST CONTROL SOLENOID Genuine OEM Nissan Boost Control Solenoid. 2009+ Nissan R35 GT-R. 14956-JF00A
	AEM REPLACEMENT PRESSURE SENSOR KITS AEM Replacement PSIg pressure sensors are available from 100-2000 psi for boost, EGT, nitrous, brake pressure, inlet air temperature, or UEGO replacement gauges. Universal Application. 30-2130-100,30-2130-150,30-2130-500,30-2130-1000,30-2130-2000
	AEM REPLACEMENT FLUID PRESSURE SENSORS AEM Replacement Fluid Pressure Sensors are available for 15, 35, 50, 100 and 150 PSI boost and fluid ranges. Compatible with AEM Analog and Digital Gauges. Universal Application. 30-2131-15G,30-2131-50,30-2131-75,30-2131-100,30-2131-150
	AEM REPLACEMENT FLUID TEMPERATURE SENSOR KIT AEM Replacement Oil/Trans/Water Temperature Sensor Kit includes the 1/8"NPT temperature sensor, plug, pins & pin lock. Compatible with digital and analog gauges. Universal Application. 30-2012
	AEM REPLACEMENT METHANOL INJECTION MONITOR SENSOR AEM Replacement Methanol Injection Monitor Sensor. Universal Application. 35-2128
	AEM REPLACEMENT ANALOG EGT K-TYPE SENSOR AEM Replacement EGT Sensor for Analog Gauges. K-Type Closed Tip Thermocouple Sensor. Universal Application. 30-2065
	AEM EXHAUST GAS TEMPERATURE SENSOR KIT The AEM 30-2050 EGT Sensor Kit is a RTD type EGT sensor with an inconel body, M14 x 6H. It includes an RTD temp sensor with male thread, a weld-on bung with female thread, connector and pins and offers a heat range of -40°F to 1832°F. Universal Application. 30-2050
	AEM UNIVERSAL 12 POSITION TRIM POT The AEM Universal 12 Position Trim Pot is for use on virtually any Engine Management System, such as the AEM EMS. Use the Trim Pot to adjust a number of trims, including ignition timing, fuel, boost, etc. Universal Application. 30-2056
R35 GT-R - CABLES & HARNESSES      ///      BACK TO TOP
	AEM INFINITY SERIES 7 UNIVERSAL PLUG & PIN KIT The AEM Infinity Series 7 Universal Plug & Pin Kit includes (1) 73-pin connector with cover, (1) 56-pin connector with cover, 130 small pins, 1 large pin with weather seal, 1 micro relay with pins, and 30 sealing plugs. AEM offers several different wiring harness types and configurations to simplify the process of wiring the Infinity ECU to your vehicle. Universal Application. 30-3701
	AEM INFINITY SERIES 7 UNIVERSAL WIRING HARNESS The AEM Infinity Series 7 Universal Wiring Harness includes pre-wired power and grounds, power relay, fuse box, dual wideband connectors, AEMnet connector (CAN), 100 X 96" terminated wires for population and 12 small pins. AEM offers several different wiring harness types and configurations to simplify the process of wiring the Infinity ECU to your vehicle. Universal Application. 30-3702
	AEM INFINITY SERIES 7 MINI UNIVERSAL WIRING HARNESS The AEM Infinity Series 7 Mini Universal Harness includes pre-wired power and grounds, power relay, fuse box, dual wideband connectors, AEMnet connector (CAN), 100 small pins with 30 sealing plugs. AEM offers several different wiring harness types and configurations to simplify the process of wiring the Infinity ECU to your vehicle. Universal Application. 30-3703
	AEM INFINITY SERIES 5 PLUG & PIN KIT The AEM Infinity Series 5 Plug & Pin Kit includes 80 pin connector with cover, 80 small pins, 1 micro relay with pins and 30 sealing plugs. AEM offers several different wiring harness types and configurations to simplify the process of wiring the Infinity ECU to your vehicle. Universal Application. 30-3704
	AEM INFINITY SERIES 5 MINI UNIVERSAL WIRING HARNESS The AEM Infinity Series 5 Mini Universal Harness includes pre-wired power, grounds, power relay, fuse box, single wideband & AEMnet, 80 small pins and 30 sealing plugs. AEM offers several different wiring harness types and configurations to simplify the process of wiring the Infinity ECU to your vehicle. Universal Application. 30-3705
	AEM INFINITY SERIES 5 UNIVERSAL MINI FLYING LEAD HARNESS The AEM Infinity Series 5 Universal Mini Flying Lead Harness includes pre-wired power, grounds, power relay, single wideband, 8 x coils & 8 x injectors. I/O wiring includes TPS, MAP, CLT, AIT, +5V, Sensor Ground, Fan, Tach & 2 Step. 10 x 96" 22ga Terminated wire and 2 x 96" Terminated 2-Pair Twisted/Shielded Wire. AEM offers several different wiring harness types and configurations to simplify the process of wiring the Infinity ECU to your vehicle. Universal Application. 30-3706
	AEM INFINITY 02 SENSOR EXTENSION HARNESS The AEM Infinity 02 Sensor Extension Harness allows you to connect your AEM wideband O2 air/fuel ratio sensors to the Infinity's on-board wideband UEGO controllers. 72" length. Universal Application. 30-3600
	AEM INFINITY AUX HARNESS FOR AIT AND MAP SENSOR The AEM Infinity Aux Harness for AIT and MAP Sensor allows you to connect your AEM AIT and MAP sensors to the Infinity's Aux Deuatch Plug. 72" length. Universal Application. 30-3510-00
	AEM INFINITY IP67 COMMUNICATIONS CABLE Protect your AEM Infinity ECU by using IP67-rated communications cables. They are completely dustproof and are rated waterproof to 1 meter. Universal Application. 30-3601
	AEM INFINITY IP67 LOGGING CABLE Protect your AEM Infinity ECU by using IP67-rated communications cables. They are completely dustproof and are rated waterproof to 1 meter. Universal Application. 30-3602
	COBB AP3 OBDII UNIVERSAL ACCESSPORT CABLE Tired of your Accessport OBDII cable getting in the way? The new COBB OBDII Universal Cable features a much lower profile OBD connector design. The 6ft cable allows for a cleaner installation when choosing to route behind the dash. Universal Application. AP3-OBDII-CABLE-UNIVERSAL
	AEM PRESSURE SENSOR REPLACEMENT HARNESS FOR DIGITAL GAUGES The AEM Digital Boost/Pressure Gauge Replacement Cable replaces your old, damaged harness. This 8 foot cable fits AEM Digital Gauges (30-4401, 30-4406, 30-4407 & 30-4408). Universal Application. 35-3405
	AEM PRESSURE SENSOR REPLACEMENT HARNESS FOR ANALOG GAUGES AEM 96" Sensor Replacement Harness for Analog Boost/Fuel/Oil Pressure Gauges. Universal Application. 35-3412
	AEM REPLACEMENT TRU-BOOST 5 BAR MAP SENSOR HARNESS AEM 96" Replacement Harness for Tru-Boost 5 Bar MAP Sensor Upgrade Universal Application. 35-3410
	AEM TRU-BOOST GAUGE REPLACEMENT CABLE The AEM True-Boost Replacement Cable fits the AEM Digital Tru-Boost Gauge (30-4350) and is 8 feet long. Universal Application. 35-3409
	AEM REPLACEMENT UEGO POWER HARNESS The AEM Replacement UEGO Power Harness is compatible with both the Bosch 4.2 & 4.9 LSU sensors. 36" length. Universal Application. 35-3401
	AEM REPLACEMENT UEGO 4.2LSU OXYGEN SENSOR HARNESS AEM 96" Replacement UEGO 4.2LSU Oxygen Sensor Harness. Universal Application. 35-3400
	AEM REPLACEMENT UEGO 4.9LSU OXYGEN SENSOR HARNESS AEM 96" Replacement UEGO 4.9LSU Oxygen Sensor Harness. Universal Application. 35-3441
	AEM WIDEBAND FAILSAFE O2 SENSOR REPLACEMENT HARNESS AEM 96" 4.2LSU O2 Sensor Replacement Harness for Wideband Failsafe Gauge 30-4900. Universal Application. 35-3426
	AEM REPLACEMENT ANALOG TEMPERATURE SENSOR HARNESS AEM 96" Replacement Temperature Sensor Harness for the Oil/Transmission/Water Temp Analog Gauges. Universal Application. 35-3413
	AEM DIGITAL VOLT GAUGE POWER REPLACEMENT HARNESS AEM 36" Power Replacement Harness for Digital Volt Gauge 30-4400. Universal Application. 35-3403
	AEM DIGITAL TEMPERATURE GAUGE REPLACEMENT HARNESS AEM 96" Replacement Harness for the Digital Oil/Transmission/Water Temperature Gauge 30-4402. Universal Application. 35-3404
	AEM REPLACEMENT METH FLOW/FAILSAFE GAUGE USB CABLE AEM 96" Replacement USB Cable for AEM Meth Flow/Failsafe Gauges. Universal Product. 35-3415
	AEM REPLACEMENT ANALOG EGT SENSOR HARNESS AEM 96" Replacement EGT Sensor Harness for Analog Gauges. Universal Application. 35-3414
	AEM WIDEBAND FAILSAFE REPLACEMENT POWER HARNESS AEM 36" Replacement Power Harness for the Wideband Failsafe Gauge 30-4900. Universal Application. 35-3425
	AEM ANALOG GAUGE POWER HARNESS AEM 36" Power Replacement Cable for Analog Gauges. Universal Application. 35-3411
	AEM REPLACEMENT METH FAILSAFE OUTPUT HARNESS AEM 36" Replacement Output Harness for Water/Methanol Failsafe Gauges. Universal Product. 35-3418
R35 GT-R - SOLENOIDS      ///      BACK TO TOP
	OEM NISSAN BOOST CONTROL SOLENOID Genuine OEM Nissan Boost Control Solenoid. 2009+ Nissan R35 GT-R. 14956-JF00A
	AEM BOOST CONTROL SOLENOID AEM's Boost Control Solenoid is specifically manufactured for automotive applications. It is designed to resist corrosion and sticking from exposure to rich fuel mixtures. AEM's Boost Control Solenoid is pressure tested to 100 PSI and includes 1/8" NPT to 3/8" barb fittings to reduce any chance of leaks. Universal Application. 30-2400
	PERRIN 3-PORT ELECTRONIC BOOST CONTROL SOLENOID The EBCS PRO operates almost 2 times faster than other designs, allowing almost 50% more airflow, and works with OEM ECUs without causing check engine lights. To fully utilize the EBCS Pro, an ECU recalibration is NEEDED to ensure no overboosting occurs. The OEM male connector is specific to all Subaru and Mitsubishi applications. Includes additional brackets to allow universal applications. Universal Application. ASM-TAC-726

CSS