 |
|
|
|
EVOLUTION X - GASKETS, SEALS & INSTALL
///
BACK TO TOP |
|
|
GRIMMSPEED EVO X INTAKE MANIFOLD GASKET
GrimmSpeed Evolution X Intake Manifold Gasket
2008-2015 Evolution X.
20007 |
|
OEM MITSUBISHI INTAKE MANIFOLD GASKET
OEM Mitsubishi Intake Manifold Gasket.
2008-2015 Evolution X.
1005A966 |
|
OEM MITSUBISHI THROTTLE BODY GASKET
OEM Mitsubishi Throttle Body Gasket.
2008-2015 Evolution X.
MN143034 |
|
|
EVOLUTION X - SENSORS
///
BACK TO TOP |
|
|
3 BAR MAP SENSOR
Genuine OEM Mitsubishi 3 Bar Map Sensor.
2008-2015 Evolution X.
1865A052 |
|
OMNI POWER MITSUBISHI MAP SENSORS
Omni Power USA 3 or 4 Bar MAP (Manifold Absolute Pressure) sensors use state of the art bipolar op amp circuitry with thin film resistor networks built into each micro chip. Pressure changes are calculated on a true linear 0-5 volt scale via a specially designed silicon pressure sensor that also compensates for temperature changes.
2008-2015 Evolution X.
MAP-MITS-3BR,MAP-MITS-4BR |
|
GENUINE OEM MITSUBISHI EVO X MASS AIR FLOW SENSOR
Genuine OEM Mitsubishi Mass Air Flow Sensor fits all 2008-2015 Mitsubishi Lancer Evolution X models.
2008-2015 Evolution X.
MR985187 |
|
AEM REPLACEMENT MAP SENSOR KITS
AEM Replacement MAP Sensor Kits include stainless steel sensor, connector, pins, 1/8" NPT to -4AN adapter & 1/8" NPT to 3/16" barb adapter. 1, 2, 3.5 and 5 BAR.
Universal Application.
30-2130-15,30-2130-30,30-2130-50,30-2130-75 |
|
AEM MAP SENSOR CONNECTOR
AEM Map Sensor Connector.
Universal Application.
35-2131 |
|
AEM AIR INLET TEMPERATURE SENSOR
Air inlet temperature sensor kit. Includes aluminum weld-in bung, connector plug with flying lead & sensor.
Universal Application.
30-2010 |
|
STM UNIVERSAL GM AIR INTAKE TEMPERATURE SENSOR KIT
For a less expensive option to the AEM sensors, The STM GM Air Intake Temperature Sensor Kit includes an aluminum weld-on bung for your pipe, GM AIT sensor and matching pigtail harness.
Universal Application.
STM-GMAIT |
|
DURALAST GM AIT SENSOR PIGTAIL HARNESS
Duralast GM air intake temperature sensor female pigtail harness. Typically used with Mitsubishi DSM & Evolution speed density conversions.
Universal Application.
235 |
|
DURALAST GM AIT SENSOR
Duralast GM 3/8" NPT air intake temperature sensor. Typically used with Mitsubishi DSM & Evolution speed density conversions
Universal Application.
SU-107 |
|
|
EVOLUTION X - FLANGES
///
BACK TO TOP |
|
|
STM EVO X MAF ADAPTER INTAKE FLANGE
The STM Aluminum MAF Adapter Intake Flange for the 2008-2015 Evolution X is machined right here in Rochester, NY and a perfect fit to any 3" aluminum pipe. A must-have for your custom intake! Stainless hardware is included.
2008-2015 Evolution X.
STM-EVOX-MAFADF |
|
ETS 3.5" MAF ADAPTER
The ETS Mitsubishi Evolution X 3.5" Maf Housing with Velocity Stack is made to replace your stock housing to allow more air flow for your high horsepower Evo X. Made with a 5" wide velocity stack to allow the use of a larger filter for maximum air flow. Optional Filter & Coupler available. This is a critical component for making high horsepower on the Evo X. If your reaching .5v on your current setup, this is needed for higher air flow.
2008-2015 Evolution X.
ETS_EVOX_35_MAF |
|
|
EVOLUTION X - INTAKE SHIELDS
///
BACK TO TOP |
|
|
STM BLACK INTAKE HEAT SHIELD
The STM Intake Heat Shield for the Evo X is designed to protect your air filter from the hot air off your fans. Made in-house of stainless steel and powder coated with a durable, gloss black finish, bolts into existing factory holes on the frame rail and includes stainless hardware for a clean and easy install.
2008-2015 Evolution X.
STM-EVOX-INSHD |
|
STM INTAKE HEAT SHIELD
The STM Intake Heat Shield for the Evo X is designed to protect your air filter from the hot air off your fans. Made in-house of stainless steel, this will bolt into existing factory holes on the frame rail and includes stainless hardware for a clean and easy install. Available with a mirror polish or the standard stainless which can be powder coated or finished to your liking.
2008-2015 Evolution X.
STM-EVOX-INSHD |
|
BUSCHUR RACING INTAKE SHIELD
When an open element filter is installed on the X there is a "stumble" issue when using the A/C. Once the engine temperature goes up the A/C fan will kick on. When this happens the hot air is forced into the air filter. This shield prevents that from occuring as it blocks the extra hot air from entering the system.
2008-2015 Evolution X.
EVOX-30007 |
|
|
|
